向家坝二纵围堰柔性结构段基础施工技术初探

向家坝水电站二期纵向围堰上游段座落于厚达45～62 m的覆盖层上，为提高接头段深厚覆盖层地基承载力，且保证导流期不同江水位时的堰体稳定，优化调整方案为，将接头段和导水段改为柔性结构。详细介绍了柔性结构段基础处理中所涉及的施工程序、施工技术和异常情况处理等。二纵围堰经过了2009年和2010年两个汛期的考验，安全监测显示与实际运行表明，柔性结构体结构稳定。将导水结构堰体改为柔性结构体，不仅节约了投资，而且保证了二期截流工程按施工总进度计划实施。     

Development of high-performance heavy density concrete using different aggregates for gamma-ray shielding

Primary and secondary containment structures are the major components of the nuclear power plant (NPP). The performance requirements of the concrete of containment structures are mainly radiological protection, structural integrity and durability, etc. For this purpose, high-performance heavy density concrete with special attributes can be used. The aggregate of concrete plays an essential role in modifying concrete properties and the physico-mechanical properties of the concrete affect significantly on its shielding properties. After extensive trials and errors, 15 concrete mixes were prepared by using the coarse aggregates of barite, magnetite, goethite and serpentine along with addition of 10% silica fume (SF), 20% fly ash (FA) and 30% ground granulated blast-furnace slag (GGBFS) to the total content of OPC for each mix. To achieve the high-performance concrete (HPC- grade M60), All concrete mixes had a constant water/cement ratio of 0.35, cement content of 450 kg/m³ and sand-to-total aggregate ratio of 40%. Concrete density has been measured in the case of fresh and hardened. The hardened concrete mixes were tested for compressive strength at 7, 28 and 90 days. In some concrete mixes, compressive strength was also tested up to 90 days upon replacing sand with the fine portions of magnetite, barite and goethite. The attenuation measurements were performed by using gamma spectrometer of NaI (Tl) scintillation detector. The utilized radiation sources comprised ¹³⁷Cs and ⁶⁰Co radioactive elements with photon energies of 0.662 MeV for ¹³⁷Cs and two energy levels of 1.173 and 1.333 MeV for ⁶⁰Co. Some shielding factors were measured such as half-value layer (HVL), tenth-value layer (TVL) and linear attenuation coefficients (μ). Experimental results revealed that, the concrete mixes containing magnetite coarse aggregate along with 10% SF reaches the highest compressive strength values exceeding over the M60 requirement by 14% after 28 days of curing. Whereas, the compressive strength of concrete containing barite aggregate was very close to M60 and exceeds upon continuing for 90 days. The results indicated also that, the compressive strength of the high-performance heavy density concrete incorporating magnetite as fine aggregate was significantly higher than that containing sand by 23%. Also, concrete made with magnetite fine aggregate improved the physico-mechanical properties than the corresponding concrete containing barite and goethite. Therefore, high-performance concrete incorporating magnetite as fine aggregate enhances the shielding efficiency against γ-rays.     

Isolation of the effect of the hairy layer length on the mechanical properties of waterborne coatings

The effect of the acidic hairy layer length on the interdiffusion of polymer between particles and as a consequence on the mechanical properties of the films produced from waterborne coatings has been studied. In order to isolate this effect, latexes with the same particle diameter and molecular weight but stabilized with poly(acrylic acid)-block-poly(butyl acrylate) (PAA-b-PBA) block copolymers of controlled and different lengths were prepared. Tensile strength measurements showed at the macroscopic level that the presence of AA chains in the particle surface reduced the mechanical properties of the films dried at room temperature, being its effect worse the longer the AA chain length. Higher annealing temperatures erased the negative effect of the acidic hairy layer on mechanical properties. The neutralization with NaOH instead of with NH₄OH also led to worse mechanical properties. These macroscopic results were supported by Fluorescence Resonance Energy Transfer (FRET) experiments that showed that at the microscopic level, the extent of interdiffusion occurred slower when the AA chains in the particles surface increased, the annealing temperature was lower and when NaOH was used as neutralizing agent instead of NH₄OH.     

Physics‐based spectral sharpening through filter‐chart calibration

The spectral overlap of color‐sampling filters increases errors when using a diagonal matrix transform, for color correction and reduces color distinction. Spectral sharpening is a transformation of colors that was introduced to reduce color‐constancy errors when the colors are collected through spectrally overlapping filters. The earlier color‐constancy methods improved color precision when the illuminant color is changed, but they overlooked the color distinction. In this article, we introduce a new spectral sharpening technique that has a good compromise of color precision and distinction, based on real physical constraints. The spectral overlap is measured through observing a gray reference chart with a set of real and spectrally disjoint filters selected by the user. The new sharpening method enables to sharpen colors obtained by a sensor without knowing the camera response functions. Experiments with real images showed that the colors sharpened by the new method have good levels of color precision and distinction as well. The color‐constancy performance is compared with the data‐based sharpening method in terms of both precision and distinction. © 2014 Wiley Periodicals, Inc. Col Res Appl, 40, 564–576, 2015     

Deep blue/ultraviolet microcavity OLEDs based on solution-processed PVK:CBP blends

There is an increasing need to develop stable, high-intensity, efficient OLEDs in the deep blue and UV. Applications include blue pixels for displays and tunable narrow solid-state UV sources for sensing, diagnostics, and development of a wide band spectrometer-on-a-chip. With the aim of developing such OLEDs we demonstrate an array of deep blue to near UV tunable microcavity (μc) OLEDs (λ ∼373–469 nm) using, in a unique approach, a mixed emitting layer (EML) of poly(N-vinyl carbazole) (PVK) and 4,4′-bis(9-carbazolyl)-biphenyl (CBP), whose ITO-based devices show a broad electroluminescence (EL) in the wavelength range of interest. This 373–469 nm band expands the 493–640 nm range previously attained with μcOLEDs into the desired deep blue-to-near UV range. Moreover, the current work highlights interesting characteristics of the complexity of mixed EML emission in combinatorial 2-d μcOLED arrays of the structure 40 nm Ag/x  nm MoO_x/∼30 nm PVK:CBP (3:1 weight ratio)/y  nm 4,7-diphenyl-1,10-phenanthroline (BPhen)/1 nm LiF/100 nm Al, where x = 5, 10, 15, and 20 nm and y = 10, 15, 20, and 30 nm. In the short wavelength μc devices, only CBP emission was observed, while in the long wavelength μc devices the emission from both PVK and CBP was evident. To understand this behavior simulations based on the scattering matrix method, were performed. The source profile of the EML was extracted from the measured EL of ITO-based devices. The calculated μc spectra indeed indicated that in the thinner, short wavelength devices the emission is primarily from CBP; in the thicker devices both CBP and PVK contribute to the EL. This situation is due to the effect of the optical cavity length on the relative contributions of PVK and CBP EL through a change in the wavelength-dependent emission rate, which was not suggested previously. Structural analysis of the EML and the preceding MoO_x layer complemented the data analysis.     

Fully solution-processed and multilayer blue organic light-emitting diodes based on efficient small molecule emissive layer and intergrated interlayer optimization

Efficient and fully solution-processed blue organic light-emitting diodes (OLEDs) based on fluorescent small-molecule and methanol/water soluble conjugated polymer as electron-injection material are reported. The emitting layer is 3,6-bis(9,9,9′,9′-tetrakis (6-(9H-carbazol-9-yl)hexyl)-9H,9′H-[2,2′-bifluoren]-7-yl)dib-nzo[b, d]thiophene 5, 5-dioxide (OCSoC) with a blue-fluorescent small-molecule, and a methanol/water soluble polymer poly[(9,9-bis(30-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl-fluorene)] (PFN) acted as electron-injection layer (EIL). All the organic layers are spin-coated from solution. The multilayer device structure with emitting layer/electron-injection layer is achieved by solution-processed method without the dissolution problem between layers. The performances of the devices show that the maximum luminous efficiency of the multilayer device is increased about 43%, compared to the single-layer device. PFN acting as the EIL material plays a key role in the improvement of the device performance when used in solution-processed small-molecule OLEDs.     

Dual closed-loops current controller for a 4-leg shunt APF based on repetitive control

ABSTRACT

Current repetitive control strategy for a 4-leg APF is usually of a poor speed in responding to the drastic changes in load harmonic profile. In this paper, a dual closed-loop current controller composed of a repetitive control-based outer loop and a PI-based inner loop is proposed to improve the performance of a 4-leg APF, with a focus on response speed and harmonic current compensation gain. The principle of the dual loop controller is explained in detail, and the stability of the system is analysed thoroughly. To further decrease the inherent time delay associated with the PWM strategy, a zero-sequence-voltage-based PWM strategy is proposed to solve the complexity in the implementation of 3D-SVPWM methods. By formulating the relationship between the duty ratio of the neutral leg control pulse and the zero-sequence-component of the reference voltages, the duty ratios of the other three legs can be calculated conveniently. The simulation and lab experiment results are provided to verify the correctness and effectiveness of the proposed dual closed-loop current controller and the zero-sequence-voltage-based PWM strategy.     

基于MF-R和AWS密钥管理机制的物联网健康监测大数据分析系统

带有传感器的可穿戴式医疗设备不断生成大量数据，由于数据的复杂性，难以通过处理和分析大数据来找到有价值的决策信息。为了解决这个问题，提出了一种新的物联网体系结构，用于存储和处理医疗应用的可扩展传感器数据（大数据）。所提出的架构主要由两个子架构组成：Meta Fog重定向（MF-R）架构和AWS密钥管理机制。MF-R架构使用Apache Pig和Apache HBase等大数据技术来收集和存储不同传感器设备生成的传感器数据，并利用卡尔曼滤波消除噪声。AWS密钥管理机制使用密钥管理方案，目的是保护云中的数据，防止未经授权的访问。当数据存储在云中时，所提出的系统能够使用随机梯度下降算法和逻辑回归来开发心脏病的预测模型。仿真实验表明，和其他几种算法相比，提出的算法具有更小的误差，且在吞吐量、准确度等方面具有一定的优越性。     

一种新的多渐消因子容积卡尔曼滤波

将强跟踪思想引入容积卡尔曼滤波（cubature Kalman filter，CKF），建立强跟踪CKF能有效克服CKF在模型不确定、状态突变等情况下，滤波性能下降的问题。通过分析现有多渐消因子计算方法，发现它们均只利用了协方差矩阵的对角线元素，并没有考虑各个状态之间的相关性，不能充分发挥多渐消因子的优势。为此，本文提出渐消因子矩阵，基于正交原理推导渐消因子矩阵的求解方法，提出多渐消因子强跟踪CKF算法。多渐消因子强跟踪CKF算法突破了传统多渐消因子为向量的限制，也不再要求渐消因子取值要大于1。仿真验证了算法具有更好的滤波精度何鲁棒性，能更好的满足工程应用的要求。     

多孔纳米碳纤维作为质子交换膜燃料电池微孔层的性能

质子交换膜燃料电池膜电极中的微孔层结构对改善体系的水管理能力，提升膜电极的整体性能发挥重要作用。本文通过静电纺丝和后续热处理的方法制备了多孔纳米碳纤维（PCNF），并以此构建膜电极的微孔层。与炭黑颗粒作为微孔层呈现出紧密堆积结构不同，由PCNF搭建的微孔层结构疏松呈现三维贯通状。膜电极的发电测试表明，以多孔纳米碳纤维作为微孔层（MPL-PCNF）的膜电极其最大功率密度达70.0mW/cm²，远高于炭黑颗粒为微孔层（MPL-CB）的膜电极（58.1mW/cm²），而没有微孔层（Ref）结构的膜电极最大功率密度仅为27.7mW/cm²，显示出PCNF作为微孔层材料的明显优势。